в‰Ў Menu

Install Second Hard Drive Hp Computer free download programs

How to Add an Extra Hard Drive (with Pictures)1. Check if you need the IDE (parallel ATA) or Serial ATA. While older computers support IDE (Parallel ATA), new ones may only support Serial ATA. If you are not sure, open the computer case and try to determine the type of the used drives from the view. It is safer to use the same type that is already installed, even if the sockets for another type also appear to be present.

IDE drives use a wide, flat ribbon cable and may have jumpers that need to be set. SATA drives have a thinner cable and no jumpers to worry about.

Install or remove a hard disk drive. To install an external hard disk. Install an extra hard disk in your PC. How to install a hard drive. Future Pinball Simpsons download free. When you first turn on the computer, your new hard disk may not be ready for use. Learn how to install a hard drive on HP and Compaq. Use the following steps to install a new hard drive into the computer. If a second hard drive was. Learn how to remove and install a new hard drive in. Adding or Replacing a Hard Drive in HP and Compaq. If you are adding a second additional drive.

Make sure you have room for an extra hard drive, here's one way to do this: Restart your computer and go into the BIOS menu. Go to the "Standard CMOS Settings Or IDE Config."In this menu, you will find four settings labeled as follows: PRIMARY MASTER: , AUTO/PRIMARY SLAVE: , SECONDARY MASTER: , SECONDARY SLAVE. Change all fields to auto detection.

Reboot your computer. Find the area where all the flat ribbon cables (or SATA cables, which are smaller and usually red) connect to the main board. Find the cable that corresponds to the free drive that was detected in step 1- 6, either primary or secondary.

Get the actual hard drive. Go to your local computer store or buy online from Newegg or another retailer. Make sure that the type (SATA or IDE (PATA)) matches. If you plan on replacing your existing hard drive (see warning on replacing drives), be sure to get one with enough space to compensate for what you're losing. Shut down your computer. Unplug all of the cords from the back of your computer and pull the computer out from the desk.

Remove the case screws. If you have a Dell, you only need to push down on the release latch(es) on the back or sides. If you're having difficulty, it's a good idea to consult your manual on how your particular case is removed.

Put the screws in a safe place so you don't lose them. Remove the side panel and place it out of the way. Find the area where all the flat ribbon cables (or SATA cables, which are smaller and usually red) connect to the main board.(fig. Find the cable that corresponds to the free drive that was detected in step 1- 6, either primary or secondary. Set the jumpers so the drive knows whether to act as a master or slave (IDE only). The jumpers are the set of pins on the back of the hard drive.

. How to install a power supply in your computer; How to install an. How to install a new hard drive in your desktop PC. install a new hard drive.

Install Second Hard Drive Hp Computer

They'll have a couple of rubber or plastic blocks covering some pins. Find the diagram or instructions for your new drive on to set the jumper for the master/slave. Note that if both the master and the slave are available on the slot you are using (primary or secondary), set the hard drive to master. Note that if you are using a SATA drive, the jumpers do not need to be changed, because each SATA device uses its own cable, and multiple IDE devices can share a cable. Find the empty bay in your computer case.

Using the screws that came with the drive or computer case, mount the drive. Connect the cable that you found in step 6 to the hard drive. If it won't go in, make sure that the safety bump is aligned with the hole.(fig. Connect a Molex power cable, (a smaller connector with red, yellow, and black wires.)(fig. A SATA drive will have a different type of power cable on the power supply. Put the side panel back on the computer and put the screws back in.

Plug all of the cables back into the rear of the computer, and connect them to their power sources if you unplugged them. Boot up the computer. Go into your BIOS at startup (most likely by pressing F1. DEL as the computer starts). Check the BIOS auto detect to ensure the second drive is detected.

On the screen that shows that primary master/slave, secondary master/slave, you should see the name of your new hard drive.

HP Support document - HP Support Center. When adding a hard drive, it important to identify the connectors on the motherboard.

The hard drive connectors on the motherboard must match the type of hard drive you wish to connect. If your motherboard has SATA data connectors and one is not in use, you can attach an additional SATA hard drive. If your motherboard has an IDE connector available, you can attach an IDE hard drive. NOTE: If you want to install a IDE hard drive to a motherboard that has only SATA data connectors, a third- party adapter is necessary. Figure 1: Motherboard with IDE and SATA data connectors.

IDE connectors. 2 - SATA data connectors. Figure 2: Example of SATA connections. Power cable. 2 - SATA data cable. Figure 3: Example of an IDE connection. IDE data cable. 2 - Power cable.